The warranty will not extend to any piece of merchandise or part there in, that has been improperly installed, abused, or neglected. All McGaughys spindles carry a lifetime warranty against manufacturers defects. Less prone to failure and loads are spread over a wider area! The kit also includes gaskets, and hardware. Mounts come undrilled, allowing you to position crossmember for any of the listed transmissions below. A small block will fit with our big block crossmember with some extra room, but a big block typically won't work with the small block crossmember. Level 3, Extreme Ride height measures approx. If you are looking for the best possible kit to convert your truck to air suspension but maintain your factory front crossmember, this is the kit for you.
Made from American made steel and laser cut, precision bent, powder coated and feature polyurethane bushings with a lifetime free replacement warranty. Our engine mounts position the engine so there is no steering interference, and our crossmember maintains the proper drive-line angle. Any cost of labor, freight, incidental or consequential damages are expressly excluded from this warranty. This mount kit includes new frame brackets that bolt into existing holes in the frame. For those swaps you'll want our big block version. All rear kits are compatible with both long and short bed trucks.
These mounts are based on a 4. This is the most functional crossmember that allows a variety of positioning based on custom engine location and mounting etc. It is engineered as a modular bolt-in unit that requires no welding. It comes with two longer bolts for install. The kit has two available Walbro fuel pump options.
They have an innovative baffling system inside to control fuel slosh and keep the pump fed even at low fuel levels and extreme driving conditions. Standard ceramic finish is polished silver, contact us for bare steel and black ceramic coated pricing. The Dropmember Rear modular suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength. Includes gaskets, bolts, reducers, and O2 sensor bungs. Warranty is limited to the repair or replacement, at McGaughys discretion, after their inspection of the defective part, once returned to McGaughys with proof of purchase, date of purchase, and all shipping costs prepaid. The Version 7 Dropmember Front suspension system is designed to replace the factory cross-member and steering system. Early small blocks with an aftermarket pan are typically safer using the big block version as well.
The Dropmember Rear modular suspension system is designed to replace the factory components and improve ride quality, performance, aesthetics, and strength. Check fit all products prior to custom painting or any form of fabrication sanding, drilling, painting, chroming, etc. Includes motor mounts, frame brackets, transmission crossmember, transmission mount, and hardware. Level 3 When combined with a 2. The included fuel pump module features an in-tank wiring harness and three ports - one for the feed line, one for the return line, and one for the vent. There are many options to complete this conversion including, oil pans, headers, fuel system, cooling, front accessories, and wiring. Our stepped headers offer great high rpm performance while retaining good low and mid-range power.
They feature a slip-fit collector that when used with stainless steel band clamps offer the best ground clearance in the industry. They're a double pass design putting the inlet and outlet on the same side which greatly simplifies plumbing to the engine. This mount was made to allow maximum clearance for routing exhaust underneath on each side. The Porterbuilt Stage 2 Deluxe Front Kit for '63-'87 Chevy Trucks replaces your factory control arms and coil springs, lowering your truck and improving handling, without replacing the factory front crossmember. The center of this conversion is our engine mounts and crossmember kit. When combined with a 2.
Muscle Rods Ceramic Coated Headers Our ceramic-coated headers offer many features that are normally only found on custom race headers. But most of all they are much stronger than any other brand available on the market. If using a late model transmission you will have to relocate your crossmember and trim for fitment. The Dropmember Front Coilover suspension system is designed to replace the factory cross-member and steering system. Includes motor mounts, frame brackets, and hardware. Our long tube headers do not work with 4wd.
These mounts are based on a 4. This is the most functional crossmember that allows a variety of positioning based on custom engine location and mounting etc. Simply measure square, bolt to transmission mount, clamp to frame, drill holes through mount and frame. See , we also offer our engine crossmember together with our motor mounts at a discounted price,. The mid-length headers use a gasket-less ball and socket type collector for a leak free install. Our Girdle is cnc machined aluminum and goes over the original mating flange, wraps around the tube, and fastens using both bolt holes. Level 1, Mild Ride height measures approx.
Less prone to failure and loads are spread over a wider area! Level 3, Extreme Ride height measures approx. Contact us for individual components. This is the most functional crossmember that allows a variety of positioning based on custom engine location and mounting etc. But most of all they are much stronger than any other brand available on the market. Please measure your original before ordering. McGaughys will not warranty any products that were modified prior to check fitting those parts on the intended vehicle.
Mounts come undrilled, allowing you to position crossmember for any of the listed transmissions below. Simply measure square, bolt to transmission mount, clamp to frame, drill holes through mount and frame. We stiffen the frame by bracing the factory motor mount brackets to the crossmember and increase over-axle clearance by keeping the tubes tucked close to the motor and rearward of the factory crossmember's location. The tanks, made specifically for your truck, feature a recessed area in the top for the fuel pump module and sending unit, so no floor modifications are needed for clearance. We offer several sizes so you can match them to your horsepower level. Prototyped and in service on our shop K5 Wally since 1998, it's now a full production item helping your truck perform better and last longer. The collector merge-spike increases power and they include gaskets, bolts, and O2 sensor bungs.