Replace the air intake hose and tighten the band clamps. Transmission fluid and the filter should be changed every 30,000 miles as well, or every two years. Carefully put new filter back on engine, avoid getting debris in filter. For further details and discussion of coolant for Cummins® engines, refer to Coolant Requirements and Maintenance, Bulletin 3666132. L-5 Ordering the Customized Parts Catalog. Make sure new gasket is properly seated on the new filter and fill filter with fresh diesel.
The full name of this particular engine was the 5. . Best oil for any diesel is Rotella a little higher to buy, but by far the best oil Tests say other wise. Do not use a fastener of lesser quality if replacements are necessary. Install the new filter on the engine. Its not in there very hard. Some cars do not includ … e changing the filter as a matter of routine maintenance.
Look and listen for changes in performance, sound, or engine appearance that can indicate service or engine repair is needed. Do not overtighten the injector hold down bolt. Cummins will pay for the lubricating oil, antifreeze, filter elements and other maintenance items that are not reusable due to the Warrantable Failure. If you still can't get the filter to loosen, use a breaker bar and cheater pipe in place of the ratchet, and pull hard - no stuck filters have been able to resist this much leverage. Make sure gasket came with the filter. . Follow the Manufacturer's Instructions for the mixture ratio.
Also, every 30,000 miles, be sure to change the engine coolant. Unscrew the lid of the filter housing and pull out the filter it is attached to the lid Remove the filter from the lid by pulling it off. Cummins is also not responsible for failures caused by incorrect oil, fuel or diesel exhaust fluid or by water, dirt or other contaminants in the fuel, oil or diesel exhaust fluid. Change the oil filter every six months, or 7,500 miles. This section of the manual provides all of the necessary information required for proper engine operation. It is recommended this be done at every fuel stop for optimum performance. The use of multigrade oil reduces deposit formation, improves.
Have the following engine data available when communicating with a Cummins® Authorized Repair Location. Run the engine enough to warm and circulate the oil, but not long enough top make the oil too hot to handle. If you know much about the motor. L-6 Service Literature Ordering Location. The gear will stay in the engine and the pump will pull free. The filter is located on driver side near the back of the engine Pain in … the rear to access. It is a metal type similar to an oil filter It has a water separator on the bottom of it.
This will cause carbon to clog the injector spray holes and piston rings, and can cause the valves to stick. I work at Cummins and we had a major warranty problem with Fram. Service locations are listed in the Cummins Worldwide Service Locator at cummins. The filter element is secured to the cap … by several locking fingers to detach the filter element from the cap carefully pry back some of the locking fingers How to change 89-98 Cummins fuel filter Here is Directions for a 94-96; A 89-93 is nearly the same but the filter is much easier to access. . .
Cummins will pay for the lubricating oil, antifreeze, filter elements and other maintenance items that are not reusable due to a Warrantable Failure. The location was determined by the factory installing the engine. The engine dataplate must not be changed unless approved by Cummins Inc. The following illustrations show examples of common dataplates used and the. Slip a plastic grocery bag, zip-lock, or bread sack under the filter and pull it up around the filter body. To unscrew the cap put a socket on the hex lug at the center of the cap. Cummins is not responsible for failures or damage resulting from what Cummins determines to be abuse or neglect, including, but not limited to: operation without adequate coolant or lubricants; overfueling; overspeeding; lack of.
The use of number 2D diesel fuel will result in optimum engine performance. . Let the oil drain while you go to the engine top. Do not use a floating ball hydrometer. C , 5W-40 synthetic engine oil. Set the filter aside to be drained.
Check for leaks around the area. W-13 All Engines International Industrial Off-Highway. Now you are ready to start the truck! Then it will fall out and you can twist it around and get to the other 4 bolts that will separate it from the power steering pump. Avoid prolonged contact with skin. Pour the old oil into jugs and drain the filter into a jug. Remove, and install the new unit in but m … ake sure to install it in the right direction. Replace with new water pump.