As long as there are no leaks afterwards. Should be located in a fremovable housing at the engine end of the upper radiator hose. The housing, thermostat, and O-ring on the V8 models is built as an assembly and will have to be replaced as such. This is critical to engine longevity and efficiency. Probably located in a removable housing at the engine end of the upper radiator hose. Replacement brand parts are the most affordable solution for all of your replacement needs! First get a bucket or container to drain the radiator fluid into.
Probably didn't need to do all of these things - but since we just purchased the truck, and given the fact that is probably hadn't been done in a while, we chose to do all of these things which really didn't cost a whole lot , it's running like a charm now. If it llook nice and greenish then just put it back in and your good to go. With AutoZone's home shipping and Same Day Store Pickup, you can get your car repair project out of the way in a flash once you order from us online. Make sure it does not slip out of that slot while putting it back on. Good luck getting the torque wrench to fit, I did the old guess method. Temperature gauge was at the top. Sep 15, 2012 there is a fuse for the windshield washer pump.
It took me some time to figure that one out. When it sticks open, it can prevent your heater from working during the winter, and if partially closed, the car can run warmer than usual. Founded in 1898, Stant manufactures world-class fuel, vapor and thermal management system parts for the automotive aftermarket. Remove the battery and battery tray. Re-fill coolant sl … owly to prevent an airlock.
Established in 1911, Gates is a leading automotive aftermarket manufacturer that specializes in belt drive, timing, fuel and cooling systems. Should be located in a removable housing at the engine end of the upper radiator hose. When the internal engine temperature is too high, the Chevy thermostat detects that the engine needs to be cooled and opens to permit coolant fluid to flow out of the engine to, and through, the cylinder block and radiator. Repair Estimate: Coolant Thermostat Replacement Coolant Thermostat Replacement The engine cooling system thermostat regulates the flow of coolant and helps maintain proper engine temperature. The O-ring seal is integral to the thermostat housing Thermostat housing-4.
When putting the new one on you will notice a slot that the thermos stat will sit snugly in. Need to have flat beded to garage I expect. Re-fill coolant sl … owly to prevent an airlock. Once that happens check for leaks one more time after you have replaced the cap and ran it under pressure for 10 minutes. I think the torque specs on the throttle body and thermostat are 18 pounds. Run engine to normal operating temperature with heater on.
Its winter and the heater is not working because of this. I think the torque specs on the throttle body and thermostat are 18 pounds. Oh, you may want to also remove the air filter and air filter housing for room. When you turn the key in your ignition, your engine turns over thanks to your engine's initial ignition spark, and warms up using peak combustion temperatures within the engine during the engine combustion process. The exhaust cross over pipe that goes between the exhaust manifolds makes the thermostat housing hard to access. Cannot be combined with any other discount or coupon.
It said something about a blown gasket. Make sure you look at which way the thermostat fits in the block so you do not put in the thermostat backwards. If you do have leaks then you never saw me before in your life. I did run over a tree limb about one hour before this happened. The thermostat is located in a hausing wher the hose bolts to the block.
You will want to save your antifreeze and put it back in. Within 3-4 minutes of driving, bell rings temp gauge goes to hot, says shut off engine. All Replacement brand items are backed by a 1-year, unlimited-mileage warranty. Shut off engine, waited 2 minutes and started back up, temp gauge back to mid point. Actual repair costs will vary based upon labor rates, time required for repair, actual parts used, your vehicle condition or other circumstances pertinent to your particular repair job. After changing the thermostat, be sure to bleed the air from the system, look for bleeder screws and run heater until air blows warm.
Brand new and durable replacement for your defective Thermostat at low price is available here. May 05, 2014 1 Remove the air intake duct hose from Mass Air Flow sensor. I sugest you get a name brand one because the generics are untrust worthy. Start engine and look for leaks. It will cause a bind and you could either break the cover in tightening it or you will definately have a leak and have to start over. Use our Approved Auto Repair Facility Locator to locate service shops and mechanics near you.