2000 chevy blazer 2 door speaker size. How do you install a speaker in a 2000 Chevy Blazer ZR2 2 2019-01-12
Replacing door speakers for 2000 chevy blazer
I took mine in, they actualy had a special price for installation of rear speakers in blazers. It should … come off. Once you get the trim panel off, spin it upside down so that the switch is facing downward. You will first need to remove the Phillips head screw holding the plastic piece on the handle. This summer, I ran a few mud boggs, for those, i used a set of 33x12.
How do you install a speaker in a 2000 Chevy Blazer ZR2 2
Then follow everyone else's instructions to carefully pry off the door around the edges. The housing is attached to the door by what looks to be four rivets. Am I going to be able to pop the rivet back in? Once you have the pannel off the speaker is easily removed with a 7mm socket or it may have tabs you just press to remove its been a while. You can find out by clicking on all the options to compare. Exterior Consumers have a choice on both two- and four-door models of either a liftgate that swings up or a tailgate that drops down. The pannels are hard to pull off because of the metal clips but they come off.
2000 Chevrolet Blazer Expert Reviews, Specs and Photos
For left and right, the drivers side should be straight ahead, as for t … he pass. I can tell you the window rocker switch comes out with two clips on the window up and down ends just put a small flathead screwdriver in-between. I made adapter plates for them and they fit great, I found the crossovers for the speakers. If you have manual windows the is a metal clip that holds the handle on that can be taken off with a flathead screwdriver. The power window button is tricky.
How do you install a speaker in a 2000 Chevy Blazer ZR2 2
Before putting the housing back in … place make sure the intake manifold and thermostat housing are both thoroughly cleaned before you put the gasket and thermostat back in place. Vehicle Overview Chevy's midsize sport ute, a rival for mainstays such as the Ford Explorer and Jeep Grand Cherokee, has a revised lineup but no substantive changes for 2000. There are push pins that hold the door on. Yeah i've never found an answer about the crossover. Three inch round speakers can clearly be made to fit. For the passenger side door, there is a screw right under the door handle and a screw in the middle underneath the door. Should tell you the size your vehicle calls for on the end of the door there should be a tag.
Chevrolet Blazer Questions
There is a pulley directly underneath your alternator that has a nut on the back of it. You'll also want to be sure to get composite headlight… Yes it will. Try to keep the other clasp in place so that you can see which direction they go. Show full review Vehicle Overview Chevy's midsize sport ute, a rival for mainstays such as the Ford Explorer and Jeep Grand Cherokee, has a revised lineup but no substantive changes for 2000. That may need to be placed, or check your vacuum switch which is located on the driver … side in the transfer case. You might want to check your vacuum hose, and vacuum switch.
How to Replace Front Door Speaker DIY
They have several replacement models, many of which are for the 4-door. You'll know what I mean when you see it. Also note, I had to remove the two trim pieces on the top half of the door before the lower panel could slide up enough to come off. On install make sure the front plastic clips are clipped in so door switch does not break see the quarter sized little plastic plate on panel to contact switch. Yes, I could have cut the wires, but I was hoping to easily re-use the connector on the new speakers. Underneath the armrest handle there are two bolts that need to be removed. ThatÂ’s all I have so fare if you get the answer e-mail me will ya.
2000 Chevrolet Blazer Expert Reviews, Specs and Photos
Inside that boot there are the wires for speakers locks windows, etc. Now firmly but gently pull up and out on the door cover. Trim upgrades are, to a certain extent, dependent on how many doors you want or will settle for. You may need an aftermarket adapter for your new speakers to fit correctly most people don't use them. The switch will pop loose and one of the silver clasps will go flying. My eventual goal was to replace the speakers.
Replacing door speakers for 2000 chevy blazer
Because the dash has a crossover installed a crossover is used to filter out certain frequencies and in this case filters out low- and midrange frequencies , most people will simply want to use a tweeter in this location. Autotrac is standard on other 4 x 4s and automatically engages when more traction is needed. Howeve,r you need to make sure that you get one with the 4 pin voltage regulator and not the 2 pin. Be careful that you don't lose it. If the power window wire is pinched or partially cut then that would be your fix. Sep 25, 2014 There is a rubber boot that goes from the body to the door.
1997 Blazer Speaker Sizes: I Have a 97 Blazer, 4 Door. I Want to ...
You can use a Dayco 506096, or a Drive-Rite 960K6 belt. If you don't use your 4wd enough you can get dry rought on the hose. Your Main window switch that can control all the windows from the driver's seat is that hub for all the power that goes to each other door and window as far as power windows is concerned. Then you need to remove the pannel, you can do this with a pannel removal tool looks like a long nail puller or you can use the less professional method of a flat head screwdriver and your hand. I just replaced mine this past weekend. Depending on the motor and what your looking to get out of it, it is very possible.
How do you install a speaker in a 2000 Chevy Blazer ZR2 2
I have to replace the outside mirror on my '95 Blazer and can't figure out how to remove door panel. Door panel has 2 small bolts under the arm rest and then 1 screw in the open handle plastic cup, then pull to remove panel, lift up to get lip off window opening. If you have a tweeter it will be in the same par as the lock and window switches. They go right on and are a perfecr fit. If not, looks like I can drill out the rivet and use a sheet metal screw.